伊人久久大香线蕉综合75,伊人久久大香线蕉AV一区,精品伊人久久久大香线蕉天堂

<th id="z4m7h"></th>

<li id="z4m7h"></li>
      Company introduction Enterprise culture National patent Quality standard Quality Promise Merchants join
      High-performance pneumatic sea The condensation sealant quali

      1 Scope


          This standard specifies the material, classification, size, requirements, test methods, inspection rules and signs, packaging and other contents of high-performance inflatable sealing devices.

      This standard applies to Anhui Huofeng Electric Co., Ltd. - high-performance inflatable plugging device product production, accessories, testing, application and installation of various standards.

      High-performance inflatable sealing device application range: waterproof sealing of different materials (steel, cement concrete, plastic) pipes for different occasions (electricity, communication, urban construction, petroleum);

          It is suitable for waterproof and anti-sand sealing of single and multiple cables, optical cables and hollow pipes, and has the functions of preventing small animals from invading and installing without dead angles;

          Pipeline repair of petroleum and petrochemical flood control, warehouse storage, and sealing of gas-filled space.

      The high-performance inflatable sealing device in this standard is referred to as HoFeG or inflatable sealed bag when it is sold in the market.


      2 normative references


          The following documents are indispensable for the application of this document. For dated references, only the dated date applies to this document. For undated references, the latest edition (including all amendments) applies to this document.

          GB/T 191 packaging storage and transportation icon

          GB/T 1040 Plastic tensile test method

          GB/T 2424.15-2008 Environmental testing for electric and electronic products - Part 3

          GB/T2828.1-2003/ISO2859-1:1999.Sampling procedures for sampling by sampling - Part 1 : Batch-to-batch sampling plan search by quality of reception (AQL)

          GB / T 2951.11-------------

      GB / T .

      GB/T 3198 aluminum and aluminum alloy foil

      GB/T 6543 single corrugated box and double corrugated box for transport packaging

      GB/T 6553 Test method for assessing resistance/electrical tracking and erosion of electrical insulating materials used under severe environmental conditions

      GB/T 6995.5-2008 Methods of identification of wires and cables - Part 5: Electrical cable insulated core identification

      GB/T 7564.11-1987 Wire and cable rubber insulation and rubber sleeves - Part 11: 180 °C rubber insulation or sheath

      GB/T 8808 soft composite plastic material peeling test method

      GB/T 9969 General guidelines for the use of industrial products

      GB/T 10004 plastic composite film for packaging, bag dry composite, extrusion compound

      General requirements for field test of GB/T 14165 metal and alloy atmospheric corrosion test

      GB 16895.3-2004 Building electrical installations - Part 5-54: Selection and installation of electrical equipment, grounding arrangements, protective conductors and protective junction conductors

      GB / T 18380.12-2008 - Tests for burning of cables and cables under fire conditions - Part 12: 1 kW pre-mixed flame test method

      GB/T 20779.2-2007 Rubber materials for electrical protection - Part 2: Rubber materials for cable accessories

      GB/T 50268 Water supply and drainage pipeline construction and acceptance specifications

      HG/T 3698 EVA hot melt adhesive

      JC/T 942 butyl rubber waterproof sealing tape

      QB/T 2358 plastic film packaging bag heat sealing strength test method

      IEC 61373:2010 Railway applications - Motor vehicle equipment - Impact and vibration tests

      IEC602364-7-729:2007 Building electrical installations - Part 7: Requirements for special installations or locations, Section 729, Operation and maintenance


      classification, naming, model  


         3.1 Product naming

      The product naming is market-oriented: HoFeG ; each product name is given the full name in combination with the product model, such as: HoFeG -40.

         3.2 According to the inner diameter of the pipeline, see Table 1.

      Table 1 Pipe inner diameter classification

      Product number

         Pipe inner diameter

      Product use range

      Product Size

      Cable diameter range (Φmm)

      HoFeG-40

      40

      120*126

      23-7.5

      HoFeG-50

      50

      120*180

      45.5-7.5

      HoFeG-63

      63

      120*230

      46.5-7.5

      HoFeG-75

      75

      120*280

      48.5-8

      HoFeG-90

      90

      120*330

      64-10.5

      HoFeG-110

      110

      120*400

      84.9-12.9

      HoFeG-125

      125

      120*450

      100-35

      HoFeG-160

      160

      140*560

      129-40

      HoFeG-180

      180

      140*650

      154-48

      HoFeG-200

      200

      140*700

      178-56

      HoFeG-250

      250

      160*900

      210-70

      HoFeG-300

      300

      180*1040

      240-95


         3.3 Naming the parts of the product

      The part names are named according to the practical type, as shown in Figure 1 and Figure 2.

      1 Product body 2 waterproof rubber strip [front and back (2PCS)] 3 non-slip rubber strip [front (2PCS)] 4 release paper       

      5 strip protective film  6 O-shaped guide ring 7 air tube  8 air tube fixed piece          

      Figure 1 front










      Figure 2 back


         3.4 Product Installation Accessories

      Product mounting accessories: lubricants, high pressure cylinders, pressure reducing valves, inflatable connectors (with pressure gauge type).


      product parts requirements 


       4.1 Product main requirements

      The main body of the inflatable sealer is: inner and outer PE/nylon co-extruded film composite alloy aluminum foil film (intermediate layer), a total of three layers.

        4.1.1 PE/nylon coextruded film material shall comply with the provisions of GB/T10004.

        4.1.2 Aluminum foil film should meet the requirements of GB/T 3198.

        

      4.2 Waterproof rubber strip

        4.2.1 Waterproof strips shall comply with the provisions of JC/T 942-2004.

        4.2.2 The width of the strip should be 30mm, the thickness should be 2mm, and the length should be cut according to the specifications of the inflatable sealer.

       

      4.3 anti-slip strip

        4.3.1 Anti-slip strips shall comply with the calibration of HG/T 3698-2002.

        4.3.2 The width of the strip should be 15mm, the thickness should be 2mm, and the length should be cut according to the specifications of the inflatable sealer.

        4.4 O-ring O-ring diameter should reach Φ 10mm. 


       4.5 air duct

         The diameter of the air duct should be Φ 2mm and the cutting length should be 300mm.

       

       4.6 release paper

        4.6.1 The surface of the release paper should be coated so that the waterproof seal can be easily peeled off when the inflatable sealer is installed.

        4.6.2 The width of the release paper shall be 57mm and the thickness shall be 0.1mm. The length shall be cut according to the specifications of the inflatable sealer.

       

      4.7 Appearance requirements


        Appearance scratches, burns, perforations, wrinkles, bubbles, trachoma delamination, impurities , are not allowed, detection methods Visual inspection   

        Heat sealing part is flat, no virtual seal, no obvious bubbles , detection method   


      4.8 Dimensional deviation Dimensional deviation is specified in Table .     


      Table  size deviation

      category

      Length degree (mm)

      Width (mm)

      Remarks

      Body material

      ±1

      ±1

      1. O-ring deviation: The deviation position of the O-ring is based on the air-guiding hole and the deviation at the intersection of the four corners. Air duct

      2. Airway deviation: The airway deviation is the length of the airway that remains on the surface of the bag.


      Waterproof strip

      ±2

      /

      Anti-slip strip

      ±2

      /

      O-ring

      ±1

      Air duct

      ± 5

      Release paper

      ±1

      /


       4.9 Physical and mechanical properties The physical and mechanical properties of    high performance inflatable sealers shall comply with the requirements of Table 3.

      Table  physical and mechanical properties


      Serial number

      project

      Claim

      Remarks

      1

      Pressure test


      The sample is mounted on PVC with an inner diameter of 110mm

      Inside the tube, there is no need to put the cable in the tube, inflate to 0.3MPa, put the pressure again to 0.45MPa after 15min, and then pressurize 0.05MPa in the sample every 15min.

      Sample burst pressure


      2

      Seal test


      Inflatable water immersion method - internal pressure of sample

      0.3MPa-0.35MPa, pipe inner diameter 110mm, pipe internal pressure 0.05MPa, room temperature, 15min.

      No continuous bubble escape



      Negative pressure test method - pressure inside the sample

      0.05 MPa, vacuum pressure - 0.5 bar, 72 h.

      No expansion, no bubble


      Water pressure test method - internal pressure of sample

      0.3MPa-0.35MPa, water pressure 5m, 30d

      No shift, leak


      3

      Axial pull test


      The internal pressure of the sample is 0.3MPa-0.35MPa.

      The inner diameter of the pipe is 150mm, the pulling force is 1kN, and it is applied for 1h.

      No shift


      4

      Bending test

      The internal pressure of the sample is 0.3MPa-0.35MPa, the inner diameter of the pipe is 150mm, the pressure in the pipe is 0.05MPa, the bending is 45°, and it is kept for 5min, each time in a direction of 90 degrees.

      No shifts, leaks and significant changes


      5

      Twist test


      The internal pressure of the sample is 0.3MPa-0.35MPa, the inner diameter of the pipe is 150mm, the pressure inside the pipe is 0.05MPa, and it is twisted to 90°. It is clockwise and counterclockwise once for 5 minutes.

      No displacement, leakage and significant changes



      6

      Low frequency vibration test


      The internal pressure is 0.05MPa, the inner diameter of the pipe is 110mm, the center of the pipe is fixed, and both ends of the cable are suspended. The frequency is 10 Hz and the peak vibration is 6 mm for 10 days.

      No shifts, leaks and significant changes



      7

      Chemical resistance test


      Chemical corrosion resistance for 30 days

      ——pH  2  NaOH  solution

      ——pH 2 HC1 solution

      ——3.5% Na SO solution

      ——3.5% NaC1 solution

      No leakage and obvious changes



      8

      Temperature cycle test


      The internal pressure is 0.05 MPa, which is maintained at 70°C for 3 h in each cycle, h at 0 °C , and h at -40 °C for 5 cycles.

      No change in air pressure, no deformation of the bag and material


      9

      Puncture test


      Special tool with tip type A-1-5-5, internal pressure 0.18MPa, vertical piercing, 300N, 60s.

      Not piercing


      10


      Extrusion test


      The internal pressure of the sample is 0.18MPa;

      --Maintain 600s under 44KN

      --Measured to withstand maximum pressure

      Not damaged

      Maximum bursting force


      Unit: kN


      11

      Single burning test


      Distance between the starting points of the carbonization sites of the lower edge of the upper bracket

      Burning down to the lower edge of the upper bracket

      Greater than 50mm

      Not more than 540mm


      Unit: mm


      12

      Mechanical properties of materials

      tensile strength

      Elongation at break

      Greater than 50MPa

      More than 150%

      Tensile unit: MPa

      Break unit: %


       4.10 Installation Instructions Requirements

         The installation instructions should comply with the provisions of GB/T9969.


      5 test methods


       5.1 Sampling method

         The raw material composite film was taken for testing, and the surface two-layer film was removed. The sample is then cut along the width of the film roll.

       5.2 Appearance

         Visual inspection under natural light, according to Table 2 appearance requirements.

       5.3 Materials

       5.3.1 Tensile properties

         According to the provisions of GB/T 1040.

       5.3.2 Peel force

         According to the provisions of GB/T 8808. The sample width is 15mm.

       5.3.3 Heat sealing strength

         After taking some film and heat sealing by machine, it is carried out according to GB/T 2358.

       5.3.4 Temperature / low pressure test

         The temperature/low pressure comprehensive test is carried out in accordance with the provisions of GB/T2424.15-2008.

       5.3.5 Mechanical performance test

         The mechanical performance test method is carried out in accordance with the provisions of GB/T2951.11-2008.

       5.3.6 Heat aging test

         The heat aging test method is carried out in accordance with the provisions of GB/T2951.12-2008.

       5.3.7 Insulation high temperature test

         The rubber insulation high temperature test is carried out according to the provisions of GB/T7594.11-1987.

       5.3.8 Piercing

         A tip type A-1-5-5 screwdriver was used to puncture a sample of three thin sheets (100 ± 2 mm in diameter) with a test speed of 200 mm/min and a puncture force of more than 100 N on all samples.    

       5.4 High performance inflatable sealer test

         a) High-performance inflatable sealer test equipment: high-pressure steel cylinder (needs lazy gas inside), pressure reducing valve, inflatable connector (set,

      With pressure gauge).

         b) First install the pressure reducing valve on the air outlet of the high pressure cylinder, then connect the air inlet connector, then connect the air inlet tube of the airtight sealer to the air inlet connector. When inflating, open the on/off valve on the high pressure steel cylinder to see the air inlet. The table of the connector is filled with the corresponding pressure gas.

       5.4.1 Pressure

      Take three samples of ISDD-110 and put them into a PVC pipe with an inner diameter of 110mm. There is no need to put the cable in the tube, inflate to 0.3MPa, put the pressure again to 0.45MPa after 15min, and then fill the sample with pressure of 0.05MPa every 15min. .

      The burst pressure of all samples was observed to exceed 0.9 MPa.

       5.4.2 Sealing test

       5.4.2.1 Inflatable water immersion method

         The sample is installed on both sides of a sealed pipe with a length of 600 mm and an inner diameter of 150 mm. The internal pressure of the sample is 0.3 MPa to 0.35 MPa, the outer diameter of the wire and cable is installed to be 55 mm, and 0.05 MPa of inert gas is input into the pipe, and then the entire device is completely immersed in the water tank for 15 minutes. . The sample should have no continuous bubbles escape from the sample installation and should be a qualified product.

       5.4.2.2 Negative pressure test

         The sample was placed in a vacuum sealing apparatus with a sample internal pressure of 0.05 MPa and a vacuum pressure of -0.05 MPa. The sample should be free of expansion and no bubble escape. After the vacuum is released, the sample returns to normal state. The diffusion time is less than 0.03 bar for 72 hours.

      If it is judged to be qualified.

       5.4.2.3 Water pressure test

         The sample was installed on the inner side of a PVC pipe with an inner diameter of 110 mm, 100 mm from the opening, and the internal pressure of the sample was 0.3 MPa to 0.35 MPa. A water injection of 5 m height was injected for 30 days. The sample was not displaced or leaked and should be a qualified product.

       5.4.3 axial pull test

         The sample was mounted on both sides of a PVC pipe with an inner diameter of 150 mm. The internal pressure of the sample was 0.3 MPa-0.35 MPa, and the outer diameter of the cable was 55 mm. The sample was pulled from the two ends with a traction force of 1 kN for 1 h. The sample is not displaced and should be a qualified product.

       5.4.4 Bending test

         The sample was installed on both sides of a PVC pipe with an inner diameter of 150 mm. The internal pressure of the sample was 0.3 MPa to 0.35 MPa, the pressure inside the pipe was 0.05 MPa, and the outer diameter of the cable was 60 mm. Pressure was applied at 650 mm from the end of the pipe to bend the extended cable into 45. °, lasting 5 min, and repeating the operation once in the direction of 90°. The sample shall be free of displacement, leakage and significant changes and shall be qualified products.

       5.4.5 Twist test

         The sample was installed on both sides of a PVC pipe with an inner diameter of 150 mm. The internal pressure of the sample was 0.3 MPa-0.35 MPa, the pressure inside the pipe was 0.05 MPa, and the outer diameter of the cable was 60 mm. 300 N was applied at 650 mm from the pipe end, and the extended cables were respectively 2 The loop/min speed is twisted 90° clockwise or counterclockwise for 5 min.

      The sample shall be free of displacement, leakage and significant changes and shall be qualified products.

       5.4.6 Low frequency vibration test

         Refer to the provisions of IEC 61373:2010. The sample was installed on both sides of a PVC pipe with an inner diameter of 150 mm. The internal pressure of the sample was 0.3 MPa-0.35 MPa, the pressure inside the pipe was 0.05 MPa, and the outer diameter of the cable was 60 mm. The pipe was fixed at the center of the pipe 600 mm from the pipe end. The ends of the cable were suspended and sinusoidal. The vibration frequency is 10 Hz, the amplitude between peaks is 6 mm, and the duration is 10 days. Check whether the sample is displaced. The sample shall be free of displacement, leakage and significant changes and shall be qualified products.

       5.4.7 Chemical resistance test

         The test samples were immersed in a chemical solution (pH 12 Na0H solution, pH 2 HC1 solution, 3.5% NaSO solution, 3.5% NaC1 solution, taken out for 30 days, and then air-dried and sealed test (inflated water immersion method). The sample has no leakage and obvious Changes should be qualified products.

       5.4.8 Test cycle test

         The sample was installed on both sides of the PVC pipe with inner diameter of 150mm. The internal pressure of the sample was 0.3MPa-0.35MPa, the pressure inside the pipe was 0.05MPa, and the outer diameter of the cable was 60mm. It was placed in the high and low circulation box and subjected to 5 high and low temperature cycle tests. (70°C3h, 0°C2h, -40°C3h is a cycle). The sample air pressure has no obvious change, and the bag body and material have no deformation and should be qualified products.

       5.4.9 Puncture test

         The sample (internal gas pressure 0.18 MPa) was vertically pierced with a special tool with a tip of A-1-5-5, and pressed downward at a speed of 2 mm/min. The pressure was increased to 300 N for 60 s. The sample is not pierced and should be a qualified product.

       5.4.10 Extrusion test

         The 90 mm x 100 mm upper and lower plates were used to squeeze the inflated sample (internal air pressure was 0.18 MPa), and the pressure was maintained for 64 s when the pressure reached 44 kN; the pressure was continuously increased, and the measured value was recorded. The sample was kept at 600kN for 600s without breaking; the post-exploration burst pressure was used as a reference record.

       5.4.11 Single Burning Test

         According to the provisions of GB/T 18380.12.

       5.4.12 Mechanical physical properties of high performance inflatable sealer body

         According to the provisions of GB/T 2951.11.


      6 inspection rules

       6.1 Batch

         The products are accepted and accepted in batches. The products of the same specification, the same process and the same raw materials are continuously produced, and the maximum batch size is not more than 5,000.

       6.2 Inspection classification

       6.2.1 Inspection is divided into factory inspection and type inspection.

       6.2.2 Factory inspection

       6.1.2.1 The inspection by the factory inspection department shall be carried out batch by batch according to this standard. After passing the inspection, the product can be shipped.

       6.1.2.2 The factory inspection items are 4.7 Appearance Requirements, 4.8 Dimensional Deviation, and 4.9 Physical Mechanical Properties: Pressure Test, Seal Test, Axial Traction Test, Bend Test, Twist Test, Low Frequency Vibration Test.

       6.2.3 Type inspection

       6.1.3.1 Type inspection shall be carried out in one of the following cases:

         a) when new products are put into production;

         b) when production is suspended for more than three months;

         c) when changing the production process or using new raw materials for production;

         d) type inspection at least once a year during normal production;

         e) When the factory inspection result is significantly different from the previous type inspection result;

         f) When the national quality supervision agency proposes to carry out type inspection requirements.

       6.1.3.2 Type inspection items are required by 4.7, 4.8, and 4.9.

       6.3 Sampling

       6.3.1 Physical and mechanical properties and other properties Random sampling methods are used to extract sufficient test specimens in each batch.

       6.3.2 Marking, Appearance and Specification Dimensions According to the sub-sampling plan specified in GB/T2828, the general inspection level II and the acceptance quality limit (AQL) are 6.5. See the informative appendix for details.

       6.4 Judgment rules

       6.4.1 Marking, dimensional deviation and appearance requirements Inspection is item by item inspection. If one item is unqualified, this sample is unqualified.

       6.4.2 Physical and mechanical properties The test results meet the requirements of this standard, and the physical and mechanical properties of the batch are judged to be qualified;

      If there is any unqualified item in the mechanical performance test result, it shall be re-sampled in the original batch, and the unqualified item shall be re-inspected. If the re-inspection result is still unqualified, the batch is judged to be unqualified.

       6.4.3 If one of the sealing performance and the pressure bearing performance is unqualified, it is judged that the batch of products is unqualified. The test results are all in line

      When required by this standard, it is judged as a good product.


      7 signs, packaging, transportation, storage


       7.1 mark

         The product shall be accompanied by a product certificate, and shall indicate the name of the manufacturer, the address of the factory, the name of the product, the specification, the implementation standard number, the quantity of the package, the net weight, the batch number, the date of manufacture, the conformity mark and the installation instructions.

       7.2 Packaging

         It can also be packaged in corrugated boxes, which can also be agreed between the supplier and the buyer.

       7.3 Transportation

         When transporting, it should prevent mechanical collision or contact with sharp objects, and must not throw and fall. It should keep the packaging intact and prevent sun and rain from being polluted by the environment.

       7.4 Storage

         It should be stored in a warehouse that is clean, cool, dry, airy, and away from heat. Stacking should be neat. The storage period shall not exceed two years from the date of production.



      Informative appendix


      The Receive Quality Limit (AQL) is 6.5, see table.


      Sampling plan


      batch

      sample

      Sample size

      Cumulative sample size

      Accepted number (Ac)

      Rejection number (Re)

      1~8

      the first

      2

      2

      0

      1

      to 15

      the first

      2

      2

      0

      1

      16 to 25

      the first

      second

      3

      3

      3

      6

      0

      0

      2

      2

      26 to 50

      the first

      second

      5

      5

      5

      10

      0

      1

      0

      2

      51 to 90

      the first

      second

      8

      8

      8

      16

      0

      3

      3

      4

      91 150

      the first

      second

      13

      13

      13

      26

      1

      4

      3

      5

      151 to 280

      the first

      second

      20

      20

      20

      40

      2

      6

      5

      7

      281 500

      the first

      second

      32

      32

      32

      64

      3

      9

      6

      10

      501  1200

      the first

      second

      50

      50

      50

      100

      5

      12

      9

      13

      1 201 to 3 200

      the first

      second

      80

      80

      80

      160

      7

      18

      11

      19

      3 201 10 000

      the first

      second

      125

      125

      125

      250

      11

      26

      16

      27

      10 001 35 000

      the first

      second

      200

      200

      200

      400

      11

      26

      16

      27

      35 001 150 000

      the first

      second

      315

      315

      315

      630

      11

      26

      16

      27

      150 001 500 000

      the first

      second

      500

      500

      500

      1000

      11

      26

      16

      27

      ≥500 001

      the first

      second

      800

      800

      800

      1600

      11

      26

      16

      27



      Friendship link:
      Phone:0551-65840466
      Mobile:13865911580
      Fax:0551-65846499
      Email:1834483879@qq.com
      Scan code attention

      Copyright ? 2018 All rights reserved. Anhui ICP for 88888888 HoFeG Electric 管理入口 Technical support:Qzwebs

      伊人久久大香线蕉综合75,伊人久久大香线蕉AV一区,精品伊人久久久大香线蕉天堂